Product Description
Z Automotive BurnBox G2
Works With:
2015-2021 Dodge Charger
2015-2021 Dodge Challenger
Note: 2018+ models require the use of a Double Bypass Harness.
Line Lock: Using one of the cruise control buttons/lever (depending on vehicle model), the BurnBox G2 uses the ABS valves to hold the vehicle with the front brakes so you can hit the gas and do a perfect burnout as long as you wish, with no wear on the rear brakes. No plumbing is required! This is a perfect alternative to the traditional plumbed-in solenoid type line lock/roll control. Super simple and cannot be detected! Gone are the days of plumbing in external solenoids in the brake system, having to bleed the brakes and run wires through the firewall to a switch.
Light Show: Using the keyfob or steering wheel buttons, turn on a light show that flashes the exterior lights in 9 different patterns.
6 pre-set patterns
3 customizable make-your-own patterns
Z Automotive Programming Utility (for Windows PCs only) is used for firmware updates and for configuration:
– Choose which exterior lights are included in the patterns
– Create your own patterns
– Choose which patterns to include or remove
– Choose which pattern to start with
– Save custom shows to file or load them from a file
– Can be enabled for in-motion use for authorized users and off-road parade use; email tech support for instructions
Button Remapping: Use the Adaptive Cruise distance buttons (when ACC is off), or install “Aux” buttons or viper cruise button bank and map the buttons for quick access to BurnBox functions.
INSTALLATION IS A SIMPLE MATTER OF PLUGGING IT INTO THE DIAGNOSTIC OBD2 PORT WHICH IS LOCATED ABOVE THE PARKING BRAKE.
Installation
Installation is a matter of simply plugging the BurnBox G2 Module into the OBDII diagnostic port under the dashboard, above the parking brake. The module will shut itself off, 30 seconds after the car goes to sleep, so there’s no need to unplug it – it’ll always be ready to use.
Operation
Line Lock: The BurnBox G2 Module will use the ABS solenoids to lock the front wheels for burnout purposes. To use this feature, you must stop the car then press the steering wheel LEFT ARROW button and hold it, and press/release the CRUISE + button. Continue to hold the LEFT ARROW button. Once the ABS light on the dash comes on (and EVIC message “Line Lock ON”), pump the brake pedal twice firmly and release. Press the gas pedal, and the rear wheels will break traction. Brakes release when the LEFT ARROW button is released. You can also use a remapped AUX button or Adaptive Cruise button for Line Lock.
Light Shows: The BurnBox G2 Module comes pre-configured with 6 light shows out of the box, plus 3 “make your own” light shows that you can configure with the ZPU utility. There are four ways to control the light shows on the BurnBox G2 Module:
Keyfob: The light show can be turned on by pressing unlock-unlock-lock-unlock from the keyfob. This will start the first light show in the sequence (depending on which show it’s configured to start with). Pressing unlock again will advance to the next enabled show. Pressing lock will turn off the light shows. You may lock the vehicle while the shows are on by pressing the button on the door handle or using the key.
Quick-on: The light show can be activated by moving the High Beam stalk to the forward (hi beam) position, and tap the CRUISE + button. This will start the first light show in the sequence (depending on which show it’s configured to start with). Pressing CRUISE + again will advance to the next enabled show. Moving the High Beam stalk back to its normal position will end the show.
Dash Menu: You can start the show by setting the dash to “Audio” mode, then press the left arrow and tap cruise CANC button. “Lightshow?” will display on the dash. Hold left arrow and tap cruise on/off (center) button to turn on the first light show in the sequence. Again to advance to the next show. Exit the menu (left arrow and CANC) to turn off the show.
AUX buttons or Adaptive Cruise buttons: See the button remap instructions below. You can use the mapped buttons to quicly access any one of the light shows. Press to toggle on/off. If the dash is set to “audio” you will see a confirmation message of the light show on or off.
The BurnBox G2 Module will shut off if it’s used for such a long time that the vehicle battery voltage drops below 11V.
Mapping AUX/ ACC buttons
If you installed the AUX button bank, the three buttons are available full-time. If you have Adaptive Cruise Control you can remap the near/far distance buttons, which will only be available when ACC is off. To remap, first place the dash in the “audio” screen. Then press and hold the left arrow button, and press the button you want to remap. Press again to switch through the options. When you get to the desired choice, let go of the left arrow.
Configuration
Configuration of the BurnBox G2 Module is accomplished by using the supplied USB cable connected to a PC, using the ZPU Programming Utility. The ZPU User Guide explains how to install ZPU and how to perform firmware updates. Please see the accompanying “Light Show Configuration Guide” to configure your BurnBox HC Module’s light show options.
Please be aware that modifying your vehicle in any way can affect your vehicle’s warranty, longevity. Please use with caution, and AT YOUR OWN RISK.
